It is currently Tue Jan 16, 2018 8:07 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: 1867 Spineless Saxon Rebuild
PostPosted: Sun May 21, 2017 3:56 pm 
Offline
Contributor
Contributor
User avatar

Joined: Tue Oct 18, 2016 3:21 pm
Posts: 388
Location: New Orleans
It took me over 10 years to get all of the parts for this rebuild.
Many years ago I got a 1867 Saxon shell with wappen, cocarde and spike with back up plate .
The spike mounting plate is SMALL about a 1/2 smaller than a standard type spike base.
I was able to find original chinstraps ( missing a few scales ) and slotted bolts along with a non perferated rear visor .

Just a couple of weeks ago I found a correct front visor that was a little off but I could get it to work.
I just finished it up after taking a birthday weekend off to work on a relatively easy project.
This is my only 1867 spineless and I feel lucky to have it.
Now how do I display it ? Front out or back out ?

I started by using a very thin drill bit in a Dremel and ran it through the holes in the visors and dome.
Then using .5 mm French waxed linen thread.
Once I found the center line on the shell and visor, I put a few stiches to hold the visor in place.

Image

I found that filing off the point on my thin 2 inch needle made all the difference in the world . A pointed needle will stick in the leather . Using a dull needle you are able to probe the holes and it makes threading SO MUCH EASIER.
I had some thin piano wire that I used to align everything up.

Image

Threading one half over and under then coming back over and under the opposite to finish the stich line.
Then repeat the other side.

Image

I had to repair a few tear outs. 100 year old leather is some what fragile
Image


Once done I did the back.

Image

The front visor trim was just a little long so I had to cut about 4mm off the ends to make it fit tight.
Image

Just a little fill o that back visor.
Image

Correct plate and cocarde. Or should the cocarde be bigger ? Don't know so this is what I am going with.

Image

The screw bolts were different sizes so I used the long bolt backing on the right side to accommodate the cocarde .
Image

I have Randy T trying to track down some screw rivets so repos will have to do for now.



Image

Image

Image

Just a few little repairs on the ear areas and screw studs and this redo is a wrap !!

Image

So this year marks this helmet at being 150 years old fitting to restore it on my 58 year birthday weekend !!

:thumb up: :thumb up: :thumb up:


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Sun May 21, 2017 5:24 pm 
Offline
Site Admin
Site Admin
User avatar

Joined: Sun Sep 04, 2005 4:52 pm
Posts: 4428
Location: Ontario CN
Congratulations Matt on doing an excellent job on that old beauty! :thumb up:

_________________
Remember, Pillage first THEN Burn ...


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Sun May 21, 2017 7:41 pm 
Online
Exceptional Contributor
Exceptional Contributor

Joined: Fri Apr 18, 2014 1:06 pm
Posts: 592
Great work. I've been working on restitching a set of visors since March and still have a way to go. Dulling the needle may work for me.


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Mon May 22, 2017 5:38 am 
Offline
Contributor
Contributor
User avatar

Joined: Sat May 02, 2015 7:26 am
Posts: 145
Location: Melbourne, Australia
Wow! Great work!


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Mon May 22, 2017 6:05 am 
Offline
Special Ranks Member
Special Ranks Member
User avatar

Joined: Mon Dec 08, 2008 6:21 am
Posts: 1542
Location: Belgium
Well done! :thumb up:
Francis


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Mon May 22, 2017 3:20 pm 
Offline
Exceptional Contributor
Exceptional Contributor
User avatar

Joined: Fri Mar 18, 2016 12:22 am
Posts: 691
Excellent job! :bravo: :bravo: :bravo:

John


Top
 Profile  
 
 Post subject: Re: 1867 Spineless Saxon Rebuild
PostPosted: Mon May 22, 2017 3:53 pm 
Offline
Contributor
Contributor
User avatar

Joined: Tue Oct 18, 2016 3:21 pm
Posts: 388
Location: New Orleans
Thanks guys !!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: aicusv and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: